Our 8.8 Grade High Tension Carriage Bolts with Square Neck for Mounting Plates of Stone Crusher Machine. Available in Sizes: M16 x 110mm & 150mm long with Special Cup Washer, Spring Washer and Nylock Nut.
Our 8.8 Grade High Tension Half Threaded Jaw crusher Keeper Plate Bolt/side liner plate bolt to fix Cheek Plates of Stone Crusher Machine. Available Spring Washer and Nylock Nut in sizes M24x90mm & 100mm long. These are Hardened and Tempered and are in AUTO BLACK FINISH for rust prevention & long life.
Conveyor Belt Fasteners Plate Hawk Jackson Type(1, 1.5, 2, 2.5, 3)
Used for joining rubber conveyor belts in Mining, Cement, Steel, Thermal, Chemical plants, Queries Road Constructions, Stone Crushing, Food, Sand & Gravels, Paper, Glass Wood, Pulp.
Usage/Application
STONE CRUSHER PLANT/ MINING
Material
Carbon Steel
Brand
PU BRAND
Roller Type
Double Sprocket Tapered Roller
Thickness
NO1, NO1.5, NO2, NO2.5, NO3.
Packaging Type
20NOS x 1BOX
Structure
Belt Conveyor
TECHNICAL SPECIFICATIONS:
Material: The plates and retaining clip are manufactured from cold rolled carbon steel sheet or strip confirming to grade D of IS:513-1973 “Specification for cold rolled carbon steel sheet (second revision)”01″ Grade D of IS:4030-1973”. Specification of cold rolled carbon steel sheet strip for general engineering purposes. These are Zinc plated for longer life and rust preventions. Specially formed teeth penetrates belt caracass without damaging conveyor belt fibre.
Screw and Nut: The screw and nut are manufactured from 4.6 of IS:1367(part 3)-1979″Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties and test methods for bolt, screws and studs with full load ability. These are painted auto black finish for longer life. Our conveyor belt fasteners ensures maximizing conveyors uptime, conveyor safety and belting productivity in a way of longer life on higher tension belts with mechanical fastener ratings up to 350KN/M(-2000P.I.W)
Selection of Fasterners
Fasteners Designation
Belt Thickness In min
Minimum Pulley Dia In min
Number Of Sets Required for Various width in mm of Belting
ELEVATOR BUCKET BOLTS PU-003 These Elevator bucket bolts are used to mounts Elevator buckets to Elevator belts and for many other mountings.
Elevator Bucket Bolts in the following sizes: 1/4×1″, 5/16×1″, 5/16×11/4″/3/8×11/2″, 3/8X2″, M8, M10 and M12, 5/16 x 1%, 5/16 x2″ Our elevator bucket bolts are painted black or zinc plated finish for longer life & rust prevention.
EURO BOLT AS PER DIN 15237 PU-004 Our Euro Bolts are with large Head Diameter provided with Domed cup washers or Flat Washer with Hex or Square nut as per customer requirements. These are used in mounting Steel Buckets & Plastic Buckets. Our Euro Bolts available in Metric Thread in M6, M8, M10 & M12 sizes with various lengths as per customer requirements. Our Euro Bolts are painted Auto black or Zinc plated finish for longer life & rust prevention. These are available in material Grade: 4.6,8.8&S.S.
Rip repair fastener is used for quick and economical lateral and longitudinal belt rip repairs. They can be easily and quickly installed with a hammer and block of wood. RIP REPAIR FASTENERS are used for Quick Joints in Rubber, PVC & Cotton Belts. Further they are very suitable for temporary repair of cracks. These fasteners can also be used for lacing belts with low Tension. The fasteners may be installed by only using a hammer and a piece of squared timber. The above fasteners are packed in 100pcs each in one box.
These fasteners are quick and easy to install in Thin PVC, Plastic, Cotton & Rubber light to medium duty conveyor belts. The fasteners staples are driven through the belt with a punch and hammer. These fasteners suitable for baggage handling, food wood and agricultural industry.
Steel Belts are manufactured from high grade quality raw materials. These are Alligator type.
Our steel belt lacing are of high durability and is designed for easy on site installation by only one person Designed for belts from 1/32″ (0.8mm) to 1/2″ (12.5mm). Belt Lacing installation requires no special tools only a hammer. Steel Belt Lacings are available in following.
Sizes: No.1, No.7, No. 15, No.20, No.25, No.27, No. 35, No. 45, No. 55, No. 65. These are available CRC Steel Stainless Steel 304 Grade.
This is MS Bolt Hinge Plate Type Fasteners with Special Fastening Bolts and Nuts suitable for Conveyor Belt 6mm to 12mm thickness available in One Meter Length. It comes with two pcs fastener with bolts and nut and one hinge pin all zinc yellow plated. Features:
Installed by Bolts and Nuts directly
Rubber belts can be repaired and back to work immediately
Belt is clamped by the fastener itself
Can be installed closer to the carcass after rubber covers are skived off
Turn fastener upside down for a more leakproof and long life
Perforated for ease of separation for troughing
Ease of installation
Friendly for the belt with less penetration points
May install the pin prior to the fastener installation
MS 45 Screw Type Belt Fastener with two Screw Holes suitable for conveyor belts 5mm to 12mmm thickness with screws and one hinge pin all Zinc Galavanized. Further MS Screw fasteners are the only mechanical fasteners which can be installed with screws using a screwdriver (battery, electric or pneumatic tool) Also available MS 65 Screw Type with Five Screws suitable for Conveyor Belts 12mm to 20mm Thick.
Does not required any SPECIAL LACING TOOL for making a LACING JOINT.
Suitable for Higher Belt ratings.
Offered is Metallic clips & Tie Rod. This works on SUPER SCREWS well seated in the CLIPS RUBBER COVERS when fightened.
Available for M-24, HR & SHR belts.
Much lasser time and skill required to make a LACING JOINT.
Our Filter Wrenches are specialized designed to remove oil filter. Our Filter Wrenches removes filters with minimal risk of damage & ideal for servicing. Screw Type wrench is provided with Steel strap with heavy-duty Plastic body and control knob. Our Oil Filters Wrench Chains are painted Auto black finish for longer & rust prevention.
Our Metal Spring Stall Clamps also known commonly as a Market Stall Clip, is a genera purpose pressed steel clamp, incorporating a heavy duty coil spring plated finish in following sizes of Spring Stall Clamps.
Spring Stall Clam (Zinc Plated Heavy) 4"/100mm with 25mm (1 inches) jaw capacity.
Spring Stall Clam (Zinc Plated Heavy) 6"/150mm with 50mm (2 inches) jaw capacity.
Spring Stall Clam (Powder Coated with Rubber Grips) 4"/100mm with 25mm (1 inches) jaw capacity.
Spring Stall Clam (Powder Coated with Rubber Grips) 6"/150mm with 50mm (2 inches) jaw capacity.
Elevator Buckets-AA Type & Shovel Type. Size: 5″ to 16″ in 1.6mm & 2mm sheet thickness in material MS CRC Steel & Stainless Steel & in Plastic Poly white Buckets in AA Type Size 4″ to 16″.
Our Square Head Bolt for Stone Crusher machine available 1″ x 4″, 5″, 6″, 8″, 9″, 10″, 12″, 14″, 16″, 18″, 20″, 22″ & 24″ Long in 4.6 Grade Material with Square Head 37mm x 37mm, Head Thickness 19mm Thread Length 2.5″ to 5″.
Taper Bolt M20 x 2.5 pitch with Square Punch available in size: Total length 76mm, Square Punch: 10mm square, Head height (including taper) 18mm Head Dia 30mm. These are Hardened and Tempered and are in AUTO BLACK FINISH for rush prevention.
These L-Type, and Knurling type fasteners, are suitable for connecting belts of a maximum thickness of 3/8 (9.5mm). One of the strongest & most secure of all types of belt fasteners for leather, hair, balata, cotton & rubber belting etc. SIZES available for 2″ to 6″ comes.
There are Designed and manufactured for Piercing Holes in all types of Belts Conveyor, Transmissions, Leather, PVC Belts, Paper Wood etc.) for Jointing These PUNCHES are manufactured in Alloy, Steels dully Hardened and Tempered. Sizes of Belt Punches. Sizes: 6mm, 8mm, 10mm, 12mm & Center Punch 4″. Our Belt Punches are Auto Black finish or Zinc Plated for longer life & rust prevention.
These BOLTS TIGHTENING KEYS are used to tighten nuts on conveyor Belt Fasteners for Joining Conveyor Belts. These Fasteners are manufactured from Alloy Steel & Hardened. Sizes of Bolt Tighten Key for Tighten Nut for conveyor Belt Fastener No. 11/2, No. 2 & No. 21/2, No. 3. We provide them in Yellow Zinc Plating Finish for longer life & rust prevention.
These BOLT BREAKERS are used to Break extra bolts left on Conveyor Belt Fasteners after Joining of Conveyor Belts.
Sizes of Bolt Breakers for breaking extra bolts from Conveyor Belt Fastener No. 11/2, No. 2 & No. 21/2, No. 3. We provide them in painted Auto black finish for longer life & rust prevention. We also provide them in Yellow Zinc Plating as per customer requirements and demand.